 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ZeroIC FEATURES TM Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module Data Sheet - Rev 2.1 AWT6331 * * * * * * * * * InGaP HBT Technology High Efficiency: 39 % @ +28 dBm output Zero Quiescent Current in Switch Mode Internal Voltage Regulation Optimized for a 50 System Low Profile Surface Mount Package: 1 mm CDMA 1XRTT, 1xEV-DO Compliant RoHS Compliant Package, 250 oC MSL-3 Suitable for BC10 (806-824 MHz) Applications band CDMA/EVDO Cell-band Wireless Handsets and Data Devices APPLICATIONS * M27 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module RF switch mode, current consumption is less than 10 A, reducing the average current consumption 70% more than a HELP2TM PA over the CDG profile. Its integrated voltage regulator eliminates the need for external components further reducing size and BOM cost. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 system. PRODUCT DESCRIPTION The AWT6331 is a new product in the revolutionary ZeroICTM PA family. The AWT6331 uses ANADIGICS' exclusive InGaP-PlusTM technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWT6331 has a unique architecture with two RF inputs. One input drives the power amplifier while the other input drives an RF switch that bypasses the power amplifier, going directly to the RF output. The mode control logic selects the PA or the RF switch. In GND at slug (pad) VEN 1 Bias Control 10 GND VMODE 2 9 GND RFIN 3 8 RFOUT RFIN_Switch 4 7 VCC VBATT 5 6 VCC Figure 1: Block Diagram 10/2008 AWT6331 GND VEN 1 10 GND VMODE 2 9 GND RFIN_PA 3 8 RFOUT RFIN_Switch 4 7 VCC VBATT 5 6 VCC GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 9 10 NAME VEN VMODE RFIN_PA RFIN_SWITCH VBATT VCC VCC RFOUT GND GND DESCRIPTION PA Enable Voltage Mode Control RF Input to PA RF Input to Switch Battery Voltage Supply Voltage Supply Voltage RF Output Ground Ground 2 Data Sheet - Rev 2.1 10/2008 AWT6331 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER Supply Voltage (VCC and VBATT) Mode Control Voltage (VMODE) Enable Voltage (VEN) RF Input Power (PIN) to PA RF Input Power (PIN) to Switch Storage Temperature (TSTG) MIN 0 0 0 -40 MAX +5 +3.5 +3.5 +10 +20 +150 UNIT V V V dBm dBm C Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER Operating Frequency (f) Supply Voltage (VCC and VBATT) Enable Voltage (VEN) Mode Control Voltage (VMODE) RF Output Power (POUT) Case Temperature (TC) MIN 824 +3.2 +2.2 0 +2.2 0 27.5(1) -30 TYP +3.4 +2.4 +2.4 28.0 MAX 849 +4.2 +3.1 +0.5 +3.1 +0.5 +85 UNIT MHz V V V dBm C PA "on", Switch "on" PA "shut down" PA Mode Switch Mode CDMA COMMENTS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.1 10/2008 3 AWT6331 Table 4: Electrical Specifications - CDMA Operation (IS-95 Modulation) (TC = +25 C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 system) PARAMETER Gain Insertion Loss Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Isolation Power-Added Efficiency (1) Enable Current Mode Control Current MIN 25 TYP 28 0.7 MAX 30.5 1.5 UNIT dB COMMENTS POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V - -50 -70 -46.5 - dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V 32 36 - -58.5 -70 40 39 <0.1 <0.01 <10 <10 -135 -40 -45 - -56 0.25 0.1 15 dBc dB % mA mA POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V RFOUT to RFIN_SWITCH, VMODE = +2.4 V, PA "on" POUT = +28 dBm, VMODE = +2.4 V through VEN pin, VEN = +2.4 V through VMODE pin, VMODE = +2.4 V VCC = +4.2 V, VEN = 0 V, VMODE = 0 V or +2.4 V VCC = +4.2 V, VEN = +2.4 V, VMODE = 0 V, Switch Mode Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 18 -133 -30 -30 2:1 A dBm/Hz 869 MHz to 894 MHz dBc VSWR POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions CW Measurement - - -65 dBc 8:1 - - VSWR Notes: (1) PAE and ACP limit applies at 836.5 MHz (IS-95 modulation). 4 Data Sheet - Rev 2.1 10/2008 AWT6331 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VEN and VMODE voltages. Power Modes The power amplifier may be placed in either a Low Power mode or a High Power mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Power Control table lists the recommended modes of operation for various applications. Table 5: Power Control APPLICATION CDMA - Switch Bypass Shutdown CDMA - PA Shutdown POUT LEVELS -* -* All POWER MODE Low Low High Shutdown VEN +2.4 V 0V +2.4 V 0V VMODE 0V +2.4 V +2.4 V 0V *Dependent upon typical output power from Transceiver and phone design. VENABLE 1 VMODE 2 3 4 VBATT 5 VENABLE VMODE RFIN_PA RFIN_SWITCH VBATT GND at slug GND GND RFOUT VCC VCC 10 9 8 7 6 VCC RFIN_PA RFIN_SWITCH C6 68 pF RFOUT C1 2.2 F C2 0.01 F GND at slug C3 330 pF C4 0.01 F C5 2.2 F Figure 3: Application Circuit Data Sheet - Rev 2.1 10/2008 5 AWT6331 PACKAGE OUTLINE Figure 4: M27 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module 6331R LLLLNN BBBBCC Figure 5: Branding Specification 6 Data Sheet - Rev 2.1 10/2008 AWT6331 COMPONENT PACKAGING Pin 1 Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE 3 mm x 3 mm x 1 mm TAPE WIDTH 12 mm POCKET PITCH 4 mm REEL CAPACITY 2500 MAX REEL DIA 7" Data Sheet - Rev 2.1 10/2008 7 AWT6331 ORDERING INFORMATION ORDER NUMBER AWT6331RM27Q7 TEMPERATURE RANGE -30 C to +85 C PACKAGE DESCRIPTION COMPONENT PACKAGING RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module AWT6331RM27P9 -30 C to +85 C ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. WARNING 8 Data Sheet - Rev 2.1 10/2008 |
Price & Availability of AWT6331
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |